- 1 Can Sonicare toothbrushes be repaired?
- 2 Why has my Sonicare toothbrush stopped working?
- 3 How do I fix a noisy Sonicare toothbrush?
- 4 What is the lifespan of a Sonicare toothbrush?
- 5 How do you reset a Sonicare toothbrush?
- 6 How do you fix a Sonicare toothbrush that won’t charge?
- 7 Can I replace my Sonicare battery?
- 8 Why did my electric toothbrush stop working?
- 9 How do you open the bottom of a Sonicare toothbrush?
- 10 How do I fix my Philips Sonicare loose shaft?
- 11 Why does my Sonicare keeps buzzing?
- 12 Why is my Sonicare buzzing charger?
- 13 Why does my electric toothbrush stop and start?
Can Sonicare toothbrushes be repaired?
If the fault with your electric toothbrush falls under the terms of the warranty and is within its warranty period, the Sonicare toothbrush repair will be free. Often, Sonicare will send out a replacement brush to replace your faulty one, rather than have you wait for the broken Sonicare toothbrush to be repaired.
Why has my Sonicare toothbrush stopped working?
The power button is stuck Toothpaste residue can build up in the small gap around the power button. This might cause the power button to get stuck and not function properly. Clean the power button and the area around it with a damp cloth to make sure it is free of debris.
How do I fix a noisy Sonicare toothbrush?
Brush head not attached properly Reattach the brush head. Make sure that the brush head is well placed and not loose or wobbly. A small gap between the handle and the brush head is normal. This is needed for vibration.
What is the lifespan of a Sonicare toothbrush?
The average lifespan of a Sonicare toothbrush, according to consumers, is anywhere from two to five years, though they are said to occasionally last up to seven.
How do you reset a Sonicare toothbrush?
Instructions on how to reset your Sonicare toothbrush
- Place your handle on the charger.
- Press and hold the power button together with the intensity button (intensity up) and the mode button for at least 2 seconds.
- You will hear 3 beeps and see the battery light flashing green.
How do you fix a Sonicare toothbrush that won’t charge?
Unplug the charger from the power outlet. Wipe the surface of the charger with a damp cloth to clean it. Set the charger out of direct sunlight and allow it to dry. When the charger is dry, plug it back into the outlet and place the Sonicare toothbrush in the charger.
Can I replace my Sonicare battery?
The rechargeable battery inside your Philips Sonicare Toothbrush cannot be replaced. If you are discarding your Sonicare Toothbrush, you can remove its battery to recycle it. For instructions on how to safely remove the battery of your toothbrush please consult your user manual.
Why did my electric toothbrush stop working?
There are two main causes for charging faults inside the toothbrush, either damaged components for example from being dropped or from water seeping inside, or a failed battery.
Push the flat edge of a metal or nylon spudger between the seal and the toothbrush body and pry it open. Do this all around the edge until the seal is partially sticking out.
How do I fix my Philips Sonicare loose shaft?
If its lose, just tighten the screw and you’re good to go. If it’s broken off, just go to Amazon.com and type: Metal Shaft for Diamond Sonic Care Toothbrush and you will find a replacement part for under $25.00. It’s just that simple. Be careful removing the water proof rubber sealants on the old shaft.
Why does my Sonicare keeps buzzing?
The vibrations of your Philips Sonicare Toothbrush weaken as the battery runs out. Fully charge your toothbrush to increase vibrations. It can take up to 24 hours to fully charge your Philips Sonicare Toothbrush. Be sure to use the original charger that came with your toothbrush.
Why is my Sonicare buzzing charger?
Sonicare vibrates on charger When placing a Sonicare toothbrush onto a charging stand that has already been connected to the power supply the handle will usually vibrate quickly once or twice as well as produce 2 beep sounds to confirm it is now charging on the stand. This is normal behaviour.
Why does my electric toothbrush stop and start?
At the end of the 2 minute cleaning cycle, the motor in the brush pauses and restarts briefly three times. This is your signal that the 2 minutes of brushing time has been achieved. Normally at this point you would turn the toothbrush off, by holding the power button for 1-2 seconds.