- 1 How do I change the battery in my Sonicare toothbrush?
- 2 Can I fix my Sonicare?
- 3 How long does a Sonicare toothbrush last?
- 4 Why is my Sonicare not vibrating?
- 5 What do you do if your Sonicare won’t charge?
- 6 How do I reset my Philips Sonicare battery?
- 7 Why does my Sonicare toothbrush keep turning on?
- 8 Why won’t my Sonicare toothbrush head come off?
- 9 Do all Sonicare brush heads fit?
- 10 Why is my Sonicare buzzing charger?
- 11 How do I fix a noisy Sonicare toothbrush?
- 12 Why is my Sonicare light flashing?
How do I change the battery in my Sonicare toothbrush?
The basic method is:
- Open and dismantle handle.
- De-solder old battery.
- Replace battery.
- Solder in new battery.
- Reassemble handle.
Can I fix my Sonicare?
If your Philips Sonicare electric toothbrush product is defective during the warranty period, Sonicare will repair or replace it free of charge.
How long does a Sonicare toothbrush last?
Average. The average lifespan of a Sonicare toothbrush, according to consumers, is anywhere from two to five years, though they are said to occasionally last up to seven.
Why is my Sonicare not vibrating?
Battery is almost empty The vibrations of your Philips Sonicare Toothbrush weaken as the battery runs out. Fully charge your toothbrush to increase vibrations. It can take up to 24 hours to fully charge your Philips Sonicare Toothbrush. Be sure to use the original charger that came with your toothbrush.
What do you do if your Sonicare won’t charge?
If the battery will not recharge, the entire Sonicare toothbrush must be replaced. Place the bottom of the Sonicare toothbrush into the charger. Plug the charger into a live outlet. Allow the toothbrush to charge for 24 hours.
How do I reset my Philips Sonicare battery?
Instructions on how to reset your Sonicare toothbrush
- Place your handle on the charger.
- Press and hold the power button together with the intensity button (intensity up) and the mode button for at least 2 seconds.
- You will hear 3 beeps and see the battery light flashing green.
Why does my Sonicare toothbrush keep turning on?
There could be a failed seal either at the button or at the top of your toothbrush that has allowed water to go in. It’s possible that the circuit board is wet from the ruined seal causing the button contacts to go on at random times. I’ve seen this happen with my sonicare toothbrush.
Why won’t my Sonicare toothbrush head come off?
To remove a brush head that’s stuck on your toothbrush, try running the toothbrush’s top section under warm water for at least ten seconds. Then, see if you can pull it off. You might have to give it quite a forceful tug, but it should come right off.
Do all Sonicare brush heads fit?
All Sonicare models are interchangeable with the others when it comes to brush heads. So you won’t have to worry too much about whether or not a specific brush head will fit your brush handle.
Why is my Sonicare buzzing charger?
Sonicare vibrates on charger When placing a Sonicare toothbrush onto a charging stand that has already been connected to the power supply the handle will usually vibrate quickly once or twice as well as produce 2 beep sounds to confirm it is now charging on the stand. This is normal behaviour.
How do I fix a noisy Sonicare toothbrush?
Brush head not attached properly Reattach the brush head. Make sure that the brush head is well placed and not loose or wobbly. A small gap between the handle and the brush head is normal. This is needed for vibration.
Why is my Sonicare light flashing?
If you see the battery indicator light blinking, or if you hear a beep, it means that your toothbrush is charging. Fully charge your Philips Sonicare Toothbrush for 24 hours. If the flashing light turns off at some point during charging, this is normal.