- 1 How do I fix my Philips Sonicare loose shaft?
- 2 How do you tighten a Sonicare actuator screw?
- 3 Why does my Sonicare rattle?
- 4 Can a Sonicare toothbrush be repaired?
- 5 Why has my Sonicare toothbrush stopped working?
- 6 How do I fix the button on my Philips Sonicare toothbrush?
- 7 How do you remove the bottom of a Philips Sonicare toothbrush?
- 8 How do I reset my Philips Sonicare toothbrush?
- 9 How long does the Sonicare toothbrush last?
- 10 Why does my Philips Sonicare keeps buzzing?
- 11 Why is my Sonicare toothbrush turning on by itself?
How do I fix my Philips Sonicare loose shaft?
If its lose, just tighten the screw and you’re good to go. If it’s broken off, just go to Amazon.com and type: Metal Shaft for Diamond Sonic Care Toothbrush and you will find a replacement part for under $25.00. It’s just that simple. Be careful removing the water proof rubber sealants on the old shaft.
How do you tighten a Sonicare actuator screw?
Take the small Phillips screwdriver. Pro tip: I experienced that the screw comes loose after just a few days if you do not take further actions. Hence, unscrew the screw completely and put some superglue at the end of it. Then tighten it again.
Why does my Sonicare rattle?
Brush head is worn If you used the same brush head for more than three months, you might need to replace your brush head. As brush heads wear out, they may start to produce more noise. We recommend replacing the brush head every three months.
Can a Sonicare toothbrush be repaired?
If the fault with your electric toothbrush falls under the terms of the warranty and is within its warranty period, the Sonicare toothbrush repair will be free. Often, Sonicare will send out a replacement brush to replace your faulty one, rather than have you wait for the broken Sonicare toothbrush to be repaired.
Why has my Sonicare toothbrush stopped working?
The power button is stuck Toothpaste residue can build up in the small gap around the power button. This might cause the power button to get stuck and not function properly. Clean the power button and the area around it with a damp cloth to make sure it is free of debris.
If the button cannot be pressed, there may be something below the button holding it down. To fix this, remove the brush from the toothbrush. Then, remove the bottom of the casing with a flat head screwdriver. If holding the toothbrush, lights facing up, depress two prongs in either side inside of the toothbrush.
No parts specified.
- Step 1 Shaft.
- Push the flat edge of a metal or nylon spudger between the seal and the toothbrush body and pry it open.
- Apply pressure to the shaft by pressing it against a firm and flat surface.
- Grab the circular, plastic base with the o-ring and pull it outward.
How do I reset my Philips Sonicare toothbrush?
Instructions on how to reset your Sonicare toothbrush
- Place your handle on the charger.
- Press and hold the power button together with the intensity button (intensity up) and the mode button for at least 2 seconds.
- You will hear 3 beeps and see the battery light flashing green.
How long does the Sonicare toothbrush last?
Average. The average lifespan of a Sonicare toothbrush, according to consumers, is anywhere from two to five years, though they are said to occasionally last up to seven.
Why does my Philips Sonicare keeps buzzing?
The vibrations of your Philips Sonicare Toothbrush weaken as the battery runs out. Fully charge your toothbrush to increase vibrations. It can take up to 24 hours to fully charge your Philips Sonicare Toothbrush. Be sure to use the original charger that came with your toothbrush.
Why is my Sonicare toothbrush turning on by itself?
There could be a failed seal either at the button or at the top of your toothbrush that has allowed water to go in. It’s possible that the circuit board is wet from the ruined seal causing the button contacts to go on at random times. I’ve seen this happen with my sonicare toothbrush.