- 1 Can a Sonicare toothbrush be repaired?
- 2 How do I fix my Philips Sonicare loose shaft?
- 3 How long should a Philips Sonicare toothbrush last?
- 4 How do I reset my Philips Sonicare battery?
- 5 Why won’t my Sonicare toothbrush head come off?
- 6 Why does my Sonicare toothbrush head keeps coming off?
- 7 Do all Sonicare brush heads fit?
- 8 What do you do if your Sonicare won’t charge?
- 9 How do you get mold out of Sonicare toothbrush?
- 10 How do I fix a noisy Sonicare toothbrush?
- 11 Why does my electric toothbrush keep breaking?
- 12 How do you fix a broken toothbrush?
Can a Sonicare toothbrush be repaired?
If the fault with your electric toothbrush falls under the terms of the warranty and is within its warranty period, the Sonicare toothbrush repair will be free. Often, Sonicare will send out a replacement brush to replace your faulty one, rather than have you wait for the broken Sonicare toothbrush to be repaired.
How do I fix my Philips Sonicare loose shaft?
If its lose, just tighten the screw and you’re good to go. If it’s broken off, just go to Amazon.com and type: Metal Shaft for Diamond Sonic Care Toothbrush and you will find a replacement part for under $25.00. It’s just that simple. Be careful removing the water proof rubber sealants on the old shaft.
How long should a Philips Sonicare toothbrush last?
It is recommended to replace your Philips Sonicare Brush Head every three months of normal use (brushing twice a day) or when the blue indicator bristles wear out.
How do I reset my Philips Sonicare battery?
Instructions on how to reset your Sonicare toothbrush
- Place your handle on the charger.
- Press and hold the power button together with the intensity button (intensity up) and the mode button for at least 2 seconds.
- You will hear 3 beeps and see the battery light flashing green.
Why won’t my Sonicare toothbrush head come off?
To remove a brush head that’s stuck on your toothbrush, try running the toothbrush’s top section under warm water for at least ten seconds. Then, see if you can pull it off. You might have to give it quite a forceful tug, but it should come right off.
Why does my Sonicare toothbrush head keeps coming off?
Brush head is not attached properly Ensure that the brush head is inserted properly and aligned in the same direction as the front handle. Note: There will be a small gap between the brush head and handle. This is normal.
Do all Sonicare brush heads fit?
All Sonicare models are interchangeable with the others when it comes to brush heads. So you won’t have to worry too much about whether or not a specific brush head will fit your brush handle.
What do you do if your Sonicare won’t charge?
If the battery will not recharge, the entire Sonicare toothbrush must be replaced. Place the bottom of the Sonicare toothbrush into the charger. Plug the charger into a live outlet. Allow the toothbrush to charge for 24 hours.
How do you get mold out of Sonicare toothbrush?
Soak the brush head. Make either a peroxide, vinegar, or bleach solution and submerge your brush head in it. This can not only remove and kill mold, but also any lingering bacteria that could infect your oral cavity. Wipe the base of the head before soaking it to help the solution more effectively remove other gunk.
How do I fix a noisy Sonicare toothbrush?
Brush head not attached properly Reattach the brush head. Make sure that the brush head is well placed and not loose or wobbly. A small gap between the handle and the brush head is normal. This is needed for vibration.
Why does my electric toothbrush keep breaking?
Internal Toothbrush Fault There are two main causes for charging faults inside the toothbrush, either damaged components for example from being dropped or from water seeping inside, or a failed battery.
How do you fix a broken toothbrush?
If your BURST brush is not charging the First step with the brush or flosser is to try a reset on your BURST Flosser or Brush. This is done by plugging the unit in to charge, Once charging go ahead and hold down the power button, After a couple of seconds all of the lights will illuminate on the unit.